[ddots-l] Re: I have audio on 3-4...FW 1884
- From: Bryan Smart <bryansmart@xxxxxxxxxxxxxx>
- To: "ddots-l@xxxxxxxxxxxxx" <ddots-l@xxxxxxxxxxxxx>
- Date: Sat, 3 Jul 2010 13:38:46 -0400
It has been a little while since I looked at the FW1884 control panel, but
there were settings in there for analog output assignments, I think. I remember
that it is/was kind of like on the ProjectMix, where software returns, like out
1/2, don't necessarily have to go to physical output 1/2. The master level in
the monitor mixer mode might be down, also. I do remember a setting in the
panel that allows the monitor mode to control the output levels.
I think that I need to just look at your DAW over Tandem. I can be available
late on tuesday afternoon. Please send a message to support@xxxxxxxxxxxxxxx
letting me know if you can be available then, and what number I should use to
reach you If Tuesday doesn't work, please propose a time later in the week.
Bryan
Bryan
-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On
Behalf Of clarence griffin
Sent: Friday, July 02, 2010 11:42 AM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: I have audio on 3-4...FW 1884
I hope its not a hardware issue.
GF
On Jul 2, 2010, at 11:40 AM, Stacy Blackwell wrote:
Yes I have, and thank you for your efforts in troubleshooting. I'm not
giving up yet! SLB
________________________________
From: goldfingas@xxxxxxxxx
Subject: [ddots-l] Re: I have audio on 3-4...FW 1884
Date: Fri, 2 Jul 2010 09:42:23 -0400
To: ddots-l@xxxxxxxxxxxxx
is your volume turned up on the fw. its the middle knob in the row of 3
right after the gains for the strips. On the right.
Just checking. You more than likely know this, but I am just going
threw different things trouble shooting.
GF
On Jul 2, 2010, at 9:26 AM, Stacy Blackwell wrote:
Hi, guys, does anybody know why the outs 3-4 will produce
audio, but outputs 1-2 still aren't working? I have checked out the drivers
tabs in Sonar and the FW 1884--they appear to be correct. I can work with
this, but I have to change all my project's Master bus' to the FW 1884's
outputs 3-4. This is no biggee; at least I can record now. But does anybody
know why outputs 1-2 won't work? Is there another place to assign the Mater
Bus' Output that overrides what is selected in the Track Pane? I'm still
scratching my head here. thanks. SLB
________________________________
The New Busy is not the too busy. Combine all your e-mail
accounts with Hotmail. Get busy.
<http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4>
________________________________
Hotmail has tools for the New Busy. Search, chat and e-mail from your
inbox. Learn more.
<http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_1>
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subjectúq or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
Other related posts:
