[duxuser] Re: Versapoint and Multiple Pages Feeding after Embossing
- From: Dave Durber <dadurber@xxxxxxxxxxxxx>
- To: duxuser@xxxxxxxxxxxxx
- Date: Sun, 25 Apr 2004 22:23:10 -0400
In my previous message, I wrote a paragraph that read:
At present, with your embosser set to 25 lines per page and DBT's
maximum lines per page also set to 25 lines per page, they both think
that a new page is required. That is why you are probably getting
multiple page breaks occurring in your documents, where you don't want
them.
It should have read:
At present, with your embosser set to 26 lines per page and DBT's
maximum lines per page also set to 26 lines per page, they both think
that a new page is required. That is why you are probably getting
multiple page breaks occurring in your documents, where you don't want
them.
I'm sorry for the error.
Sincerely:
Dave Durber
On Sun, 25 Apr 2004 22:08:55 -0400, you wrote:
>This is a case of "elementary, dear Watson" as Sherlock Holmes would
>say to Dr. Watson.
>
>Where you have embossers that need the number of lines per page to be
>specified as one of the parameters in any of their setup menus, you
>need to allow two extra lines over and above the maximum and desired
>lines per page that are specified in DBT.
>
>So, for example, if you are using paper that is 11 inches from
>perforation to perforation, you should specify 27 lines per page.
>
>In DBT, you should specify both the maximum and desired lines per page
>to be 25. By doing that, DBT becomes the controller as to when page
>breaks occur in any document.
>
>By the way, these are the settings I used to use when I owned my
>Enabling Technologies embossers. So I know they work.
>
>At present, with your embosser set to 25 lines per page and DBT's
>maximum lines per page also set to 25 lines per page, they both think
>that a new page is required. That is why you are probably getting
>multiple page breaks occurring in your documents, where you don't want
>them.
>
>I am not sure if this is the case with DBT, but with older versions of
>Duxbury products, such as DuxWp, the program used to issue a hard
>carriage return at the end of line 25 and then issue a hard page
>break. So, in fact, there were actually 26 lines per page, 25 lines
>of text, with a carriage return at the end of line 25 which produced a
>blank line 26, then the page break command.
>
>Sincerely:
>
>Dave Durber
>
>On Sat, 24 Apr 2004 00:26:41 -1000, you wrote:
>
>>I'm using an old Versapoint with Duxbury 10.4. I'm embossing a document with
>>no page codes or new line codes at the end of it. I looked at the global
>>settings and made sure that Interpoint wasn't checked. My lines per page in
>>DBT is set to 26, and on the Versapoint, it's set to 26 as well; in DBT the
>>desired lines is set to 25, and the document is less than that. Why do extra
>>pages get fed through the embosser after a document is embossed? Is there a
>>way to prevent extra pages from being sent?
>>
>>Thanks,
>>Dani
>>
>>
>>* * *
>>* This message is via list duxuser at freelists.org.
>>* To unsubscribe, send a blank message with
>>* unsubscribe
>>* as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also
>>* subscribe, unsubscribe, and set vacation mode and other subscription
>>* options by visiting //www.freelists.org. The list archive
>>* is also located there.
>>* Duxbury Systems' web site is http://www.duxburysystems.com
>>* * *
>
>
>* * *
>* This message is via list duxuser at freelists.org.
>* To unsubscribe, send a blank message with
>* unsubscribe
>* as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also
>* subscribe, unsubscribe, and set vacation mode and other subscription
>* options by visiting //www.freelists.org. The list archive
>* is also located there.
>* Duxbury Systems' web site is http://www.duxburysystems.com
>* * *
* * *
* This message is via list duxuser at freelists.org.
* To unsubscribe, send a blank message with
* unsubscribe
* as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also
* subscribe, unsubscribe, and set vacation mode and other subscription
* options by visiting //www.freelists.org. The list archive
* is also located there.
* Duxbury Systems' web site is http://www.duxburysystems.com
* * *
Other related posts:
