Fangyi,
Actually not. I choose to not DOCUMENT a flow when the terminus Rx has a
GetWave and any one of the upstream Rx are Init-Only. The EDA tool need not
discard them, there are numerous flows that the EDA tool can use.
Secondly, any of the upstream Rx can be converted to Dual by the model
maker. What you have proposed in your BIRD is to add IR outputs to the
AMI_Init function so that an EDA tool can implement a proxy AMI GetWave,
which as I said in the previous line the model maker can do as easily in
IBIS 6.1 by instead of adding these IR to the AMI_Init output, storing these
IR in the AMI_model_memory, and implementing an AMI_GetWave which does the
trivial job of convolving these IR with the AMI_GetWave input.
Walter
Walter Katz
wkatz@xxxxxxxxxx <mailto:wkatz@xxxxxxxxxx>
Phone 303.449-2308
Mobile 303.335-6156
From: RAO,FANGYI (K-USA,ex1) [mailto:fangyi_rao@xxxxxxxxxxxx]
Sent: Tuesday, May 16, 2017 2:56 AM
To: Bob Miller (APD) <bob.miller@xxxxxxxxxxxx>; Walter Katz
<wkatz@xxxxxxxxxx>
Cc: IBIS-ATM <ibis-macro@xxxxxxxxxxxxx>
Subject: RE: [ibis-macro] Re: Summary of discussion about BIRD 166.2
Bob,
The revision in BIRD166.3 is asking the EDA tool to discard all the GetWave
functions in the system, including those in your models, if one Init-only
model is present, even for valid combinations of Init-only and dual models.
Regards,
Fangyi
From: Bob Miller (APD) [mailto:bob.miller@xxxxxxxxxxxx]
Sent: Thursday, May 11, 2017 8:03 AM
To: Walter Katz <wkatz@xxxxxxxxxx <mailto:wkatz@xxxxxxxxxx> >
Cc: RAO,FANGYI (K-USA,ex1) <fangyi_rao@xxxxxxxxxxxx
<mailto:fangyi_rao@xxxxxxxxxxxx> >; IBIS-ATM <ibis-macro@xxxxxxxxxxxxx
<mailto:ibis-macro@xxxxxxxxxxxxx> >
Subject: Re: [ibis-macro] Re: Summary of discussion about BIRD 166.2
So I need a bit of clarification:
Does Walter's tweak eliminate Fangyi's objection?
Fangvi?
Regards,
Bob
On Thu, May 11, 2017 at 7:58 AM, Walter Katz <wkatz@xxxxxxxxxx
<mailto:wkatz@xxxxxxxxxx> > wrote:
Fangyi,
I would like to reference what the Redriver/Retimer flow says about the time
domain flow:
Step 7. The simulation platform performs simulation on the upstream channel,
which consists of Tx1, physical channel 1, and Rx1, according to the AMI
flow defined in the specification for channels without Repeaters.
Step 8a. Redriver: The simulation platform uses the signal waveform at the
output end of Rx1’s algorithmic model in step 7, regardless whether Rx1’s
AMI_GetWave exists or not, as the stimulus of Tx2’s algorithmic model,
regardless whether Tx2’s AMI_GetWave exists or not, and performs simulation
on the downstream channel, which consists of Tx2, physical channel 2 and
Rx2, according to the AMI flow defined in the spec for channels without
Redrivers.
Step 8b. Retimer: The simulation platform samples the output waveform of
Retimer Rx AMI_GetWave at ½ UI after each clock tick returned by the
function, generates a digital stimulus as the input to Tx2’s algorithmic
model, regardless whether Tx2’s AMI_GetWave exists or not, and performs
simulation on the downstream channel, which consists of Tx2, physical
channel 2 and Rx2, according to the AMI flow defined in the spec for
channels without Redriver. The logic level of the digital stimulus is 1 if
sampled value >= Rx1’s Rx_Receiver_Sensitivity and 0 if sampled value
<= -Rx1’s Rx_Receiver_Sensitivity. If –Rx1’s Rx_Receiver_Sensitivity <
sampled value < Rx1’s Rx_Reciver_Sensitivity, the logic level is unchanged
from the previous bit. The digital stimulus has values of -½ volt for logic
0 and +½ volt for logic 1.
The flow that Fangyi refers to (highlighted RED) when Tx2 and Rx2 do not
have an AMI_GetWave is on page 178.
Step 6c. If Tx GetWave_Exists is False and Rx GetWave_Exists is False, the
output of Step 4 is convolved with the output of Step 3 by the EDA tool and
the result is passed on to Step 8.
Where
Step 3. The output of Step 2 is presented to the Rx executable model file’s
AMI_Init function and the Rx AMI_Init function is executed. The Rx AMI_Init
function may modify the impulse response or choose to leave it unchanged.
Step 4. The EDA tool produces a digital stimulus waveform. A digital
stimulus waveform is 0.5 when the stimulus is "high", -0.5 when the stimulus
is "low", and may have a value between -0.5 and 0.5 such that transitions
occur when the stimulus crosses 0.
Where does this digital stimulus come from. There is only one digital
stimulus in the Redriver Channel, it is the digital stimulus that is the
input to Tx1. When this stimulus is convolved with the IR output of Rx2 then
all works perfectly well.
Fangyi has represented the meaning of “according to the AMI flow defined in
the spec for channels without Redrivers” as using the non-digital stimulus
output of Rx1 as the waveform to convolve with the output of Rx2 AMI_Init,
but the “spec for channels without Redrivers” call for convolving the output
of Rx AMI_Init with a digital stimulus.
The following corrects step 8a in the existing IBIS 6.1 specification to
clarify that there are two cases for time domain simulations. One with Rx1,
Tx1, Tx2 and Rx2 having an AMI_GetWave, and one with Rx1, Tx1, Tx2 or Rx2
not having an AMI_GetWave. Note that the time domain flow in the second case
will not include any of the AM_GetWave functions that do exist. Unless Rx1,
Tx1, Tx2 and Rx2 are Dual Models any Redriver flow is problematic. It should
be noted that any AMI_Init only model can be enhanced to include an
AMI_GetWave. An alternative solution to this is to enhance IBIS to include
additional IR outputs of AMI_Init that describes the equalization of the
model so that the simulator can implement a proxy AMI_GetWave function when
the AMI_GetWave function does not exist.
Step 8a. Redriver when Tx1, Rx1, Tx2 and Rx2 have AMI_GetWave: The
simulation platform uses the signal waveform at the output end of Rx1’s
algorithmic model in step 7 as the stimulus of Tx2’s algorithmic model and
performs simulation on the downstream channel, which consists of Tx2,
physical channel 2 and Rx2, according to the AMI flow defined in the spec
for channels without Redrivers.
Step 8b. Redriver when Tx1, Rx1, Tx2 or Rx2 do not have AMI_GetWave: The
output of Step 4 according to the AMI flow defined in the specification for
channels without Repeaters. is convolved with the output of Step 6a by the
EDA tool and the result is passed on to Step 8 according to the AMI flow
defined in the specification for channels without Repeaters.
Step 8c. Retimer: The simulation platform samples the output waveform of
Retimer Rx AMI_GetWave at ½ UI after each clock tick returned by the
function, generates a digital stimulus as the input to Tx2’s algorithmic
model, regardless whether Tx2’s AMI_GetWave exists or not, and performs
simulation on the downstream channel, which consists of Tx2, physical
channel 2 and Rx2, according to the AMI flow defined in the spec for
channels without Redriver. The logic level of the digital stimulus is 1 if
sampled value >= Rx1’s Rx_Receiver_Sensitivity and 0 if sampled value
<= -Rx1’s Rx_Receiver_Sensitivity. If –Rx1’s Rx_Receiver_Sensitivity <
sampled value < Rx1’s Rx_Reciver_Sensitivity, the logic level is unchanged
from the previous bit. The digital stimulus has values of -½ volt for logic
0 and +½ volt for logic 1.
Walter
Walter Katz
wkatz@xxxxxxxxxx <mailto:wkatz@xxxxxxxxxx>
Phone 303.449-2308 <tel:(303)%20449-2308>
Mobile 303.335-6156 <tel:(303)%20335-6156>
From: ibis-macro-bounce@xxxxxxxxxxxxx
<mailto:ibis-macro-bounce@xxxxxxxxxxxxx>
[mailto:ibis-macro-bounce@xxxxxxxxxxxxx ;
<mailto:ibis-macro-bounce@xxxxxxxxxxxxx> ] On Behalf Of RAO,FANGYI
(K-USA,ex1)
Sent: Thursday, May 11, 2017 3:31 AM
To: IBIS-ATM <ibis-macro@xxxxxxxxxxxxx <mailto:ibis-macro@xxxxxxxxxxxxx> >
Subject: [ibis-macro] Re: Summary of discussion about BIRD 166.2
All,
One unanimous agreement reached at the May 9 ATM that is missing in Walter’s
summary is that BIRD166.2 introduces artificial inflation of redirver
nonlinearity (e.g. limiting mode and compression), noise and crosstalks.
BTW, GetWave-only is a model problem but not a flow problem.
Regards,
Fangyi
From: ibis-macro-bounce@xxxxxxxxxxxxx
<mailto:ibis-macro-bounce@xxxxxxxxxxxxx>
[mailto:ibis-macro-bounce@xxxxxxxxxxxxx] On Behalf Of Walter Katz
Sent: Wednesday, May 10, 2017 5:16 AM
To: IBIS-ATM <ibis-macro@xxxxxxxxxxxxx <mailto:ibis-macro@xxxxxxxxxxxxx> >
Subject: [ibis-macro] Summary of discussion about BIRD 166.2
All,
Let me summarize the discussion we had on May 9 about BIRD 166.2 by
describing five scenarios, and then some concluding remarks.
Scenario 1, all four AMI models in the Redriver flow (Tx1, Rx1, Tx2, Rx2)
are Init Only models.
The current flow in IBIS 6.1 is flawed because the Rx2 AMI_Init function
does not receive the complete IR input to properly determine its
equalization.
There is unanimous agreement that BIRD 166.2 fixes this for statistical
simulations.
Scenario 2, all four AMI models in the Redriver flow (Tx1, Rx1, Tx2, Rx2)
are Dual models.
The current flow in IBIS 6.1 is flawed because the Rx2 AMI_Init function
does not receive the complete IR input to properly determine its
equalization.
There is unanimous agreement that BIRD 166.2 fixes this for both statistical
and time domain simulations.
Scenario 3, the Tx1 and Rx1 AMI models are Dual Models and the Tx and Rx2)
are Init Only models.
The current flow in IBIS 6.1 is flawed because the Rx2 AMI_Init function
does not receive the complete IR input to properly determine its
equalization.
There is unanimous agreement that BIRD 166.2 fixes the statistical flow, but
the time domain flow remains problematic.
Scenario 4, all four AMI models in the Redriver flow (Tx1, Rx1, Tx2, Rx2)
are a combination of Init Only and Dual models.
The current flow in IBIS 6.1 is flawed because the Rx2 AMI_Init function
does not receive the complete IR input to properly determine its
equalization.
There is unanimous agreement that BIRD 166.2 fixes the statistical flow, but
the time domain flow remains problematic.
Scenario 5, one or more of the four AMI models in the Redriver flow (Tx1,
Rx1, Tx2, Rx2) are GetWave Only models.
There is no valid statistical flow.
The conclusion is that BIRD 166.2 is the correct statistical flow when all
four AMI models in the Redriver flow (Tx1, Rx1, Tx2, Rx2) are a combination
of Init Only and Dual models, and is the correct time domain flow when all
four models are Dual Models.
What I believe IBIS should do is:
1. Approve BIRD 166.2
2. Recommend that all four AMI models in the Redriver flow (Tx1, Rx1, Tx2,
Rx2) are Dual Models in order to support Time Domain flow.
a. Note that any Init Only AMI model can easily be upgraded by the model
maker to a Dual Model.
3. Enhance IBIS AMI by adding additional IR outputs to the AMI_Init
function
that contain the linear (CTLE) and non-linear (DFE) equalization of the
model. (Keysight AMI_Init Enhancement)
Which leads to the following questions:
1. Is the Keysight AMI_Init Enhancement necessary if all AMI Models are
Dual Models?
2. Is it easier for a model maker to implement the Keysight AMI_Init
Enhancement instead of making Dual Models?
3. If a model maker is too lazy to make a Dual Model, will he be too lazy
to
implement the Keysight AMI_Init Enhancement?
4. Will the EDA tools that are used by model makers implement the Keysight
AMI_Init Enhancement?
Note that the Keysight AMI_Init Enhancement does not address the problem of
AMI_GetWave only models.
Walter
Walter Katz
wkatz@xxxxxxxxxx <mailto:wkatz@xxxxxxxxxx>
Phone 303.449-2308 <tel:(303)%20449-2308>
Mobile 303.335-6156 <tel:(303)%20335-6156>
