[raspberry-vi] Re: Page update

  • From: Gregory Osborne <Gregory.Osborne@xxxxxx>
  • To: "raspberry-vi@xxxxxxxxxxxxx" <raspberry-vi@xxxxxxxxxxxxx>
  • Date: Fri, 30 Dec 2016 20:04:22 +0000

Jack,
You may want to try following Mike's instructions regarding running ldconfig -p 
| grep ilctts
If it doesn't show anything - in other words, throws you back to a prompt with 
no seeming output, then run ldconfig -p

You may have to do this with sudo. I.E. sudo ldconfig -p
But then repeating ldconfig -p | grep ilctts
Should show the ilctts library loaded.
Then re-try your configuration / making of piespeakup.

Hope this helps,
Greg


---Original Message-----
From: raspberry-vi-bounce@xxxxxxxxxxxxx 
[mailto:raspberry-vi-bounce@xxxxxxxxxxxxx] On Behalf Of Jack Falejjczyk
Sent: Friday, December 30, 2016 1:57 PM
To: raspberry-vi@xxxxxxxxxxxxx
Subject: [raspberry-vi] Re: Page update


*** This is an EXTERNAL email. Please exercise caution. DO NOT open attachments 
or click links from unknown senders or unexpected email. - STS-Security***


Now I have a pretty unusual error message after installing ilctts. I wget 
piespeakup-1.0.0.tar.gz, then tar xfz piespeakup-1.0.0.tar.gz cd 
piespeakup-1.0.0 ./configure
Error: Espeak_initialize was not found in libspeak.
Tried sudo ./configure and that produced the same results.
Also, sudo modprobe speakup_soft
And no luck.

On 12/30/16, Mike Ray <mike@xxxxxxxxxxxxxxx> wrote:

Hello

I have updated the page at:

http://www.raspberryvi.org/stories/stuttering.html

With the installation instructions for both the OMX audio code library 
and piespeakup.

You may need to refresh your browser cache.

I am about to remove the broken armv7 Arch image from the downloads 
page but I will leave the armv6 image because it works on all versions.

I noticed that there is now a 64-bit Arch image for the Pi3, so I may 
try that, but there is little benefit to be had from 64-bit code with 
only a gigabyte of RAM.

Next job...write an Emacspeak server which uses the OMX code, and Rill 
will be one happy lady.

I already have a BNF Bison parser written for the Emacspeak protocol, 
just need to extend it a bit and interface it to OMX.

Mike


--
Michael A. Ray
Analyst/Programmer
Witley, Surrey, South-east UK

Eyes-free Linux:
http://eyesfreelinux.ninja/

Raspberry VI:
http://www.raspberryvi.org/

===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry 
Pi Foundation.

This list is not affiliated to the Raspberry Pi Foundation and the 
views and attitudes expressed by the subscribers to this list do not 
reflect those of the Foundation.

Mike Ray, list creator, January 2013


===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi 
Foundation.

This list is not affiliated to the Raspberry Pi Foundation and the views and 
attitudes expressed by the subscribers to this list do not reflect those of the 
Foundation.

Mike Ray, list creator, January 2013

=========================================================== 
The raspberry-vi mailing list 
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi 
Foundation.

This list is not affiliated to the Raspberry Pi Foundation and the views and 
attitudes expressed by the subscribers to this list do not reflect those of the 
Foundation.

Mike Ray, list creator, January 2013

Other related posts: