Hi, Tim. Yes I have if you are referring to the bus pane in the track view. I have loaded different songs from different folders and none of them have audio. But, if you are referring to a menu and not the bus pane to check out the Master bus' output, where else would I look? Thanks. SLB > From: tim@xxxxxxxxxxxxx > To: ddots-l@xxxxxxxxxxxxx > Subject: [ddots-l] Re: FW 1884 - no audio > Date: Wed, 30 Jun 2010 16:01:27 +0100 > > Hi, > > I'd also double-check that the output of your master bus is set to go out to > the FW1884. > > Best wishes. > > Tim Burgess > Raised Bar Ltd > Phone: +44 (0)1827 719822 > Mobile: 07989 486976 > Web: http://www.raisedbar.net > Facebook: > http://www.facebook.com/pages/Atherstone-United-Kingdom/Raised-Bar-Ltd/12023 > 4896800 > > Don't forget to vote for improved access to music and music technology at > > http://www.raisedbar.net/petition.htm > > > > -----Original Message----- > From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On > Behalf Of Stacy Blackwell > Sent: 30 June 2010 15:20 > To: ddots-l@xxxxxxxxxxxxx > Subject: [ddots-l] Re: FW 1884 - no audio > > Hmmmm....Phil, I'm not sure. It's the same that came with it brand new two > years ago. I will check. > > My wife saw the song playing on the DAW screen last night, but there were no > stereo meter lights moving on the FW 1884 to indicate the output signal's > volume. Of course I couldn't tell her if that these meters exist or not ont > he FW 1884 cause I've never seen them. > > Hey, Phil, would you also tell me again about resetting the MIDI and unity > gain? Is it Control F8 and F10 or is it Control+Shift F8 and F10. I've > done both but I want to be sure. Thanks. > SLB > > > > ________________________________ > > From: info@xxxxxxxxxxxxxxxxxxxxxxxxxxx > To: ddots-l@xxxxxxxxxxxxx > Subject: [ddots-l] Re: FW 1884 - no audio > Date: Tue, 29 Jun 2010 22:43:22 +0100 > > > > Which firmware are you running on the FW-1884? > > > > ________________________________ > > From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On > Behalf Of Stacy Blackwell > Sent: 29 June 2010 20:42 > To: ddots-l@xxxxxxxxxxxxx > Subject: [ddots-l] Re: FW 1884 - no audio > > > > Hey, guys, thanks for the advice. I don't know if I was clear or not, but I > didn't just install the FW 1884 and Sonar. I've had this same system now > for almost two years. As far as enabling or changing a checkbox somewhere, > I know I didn't do that in my last session because everything worked fine. > Unless, of course, I accidentally did something in closing out and shutting > down. Also, recall that I was the one with the Video Intercept problem that > was fixed simply by plugging up a new monitor. My DAW is possessed I > believe! The down arrow and the letter r didn't work my last couple of > sessions, so I knew it was time to replace the battery in my keyboard. > Well, last night after going into the Note Pad Caketalk Tutorial, the two > keys started working again properly and began working again in Sonar. So, > I'm sure it's a little thing that has happened, but I don't know where to > begin, and I'm not a techee. I will look under the Options menu for Audio > and look at that and also check out the drivers. I must admit I really > don't know what I'm looking for, so wish me luck. Hey, if the sound is > getting "to" the FW 1884 from Sonar, then shouldn't there be meter lights > flashing up and down to the master volume? So if there are lights, then the > problem would be in the FW 1884, right? And if no lights are indicating > volume during playback of a song, then the problem could be in Sonar. I > will have to get some eyes to check this out. Okay, guys, thanks. > Does anybody else have any suggestions? SLB > > > ________________________________ > > From: m-christer@xxxxxxxxxxxxx > To: ddots-l@xxxxxxxxxxxxx > Subject: [ddots-l] Re: FW 1884 - no audio > Date: Mon, 28 Jun 2010 18:17:52 +0000 > > Are you sure you've enabled the relevant input/output drivers, both in the > FW's ctrl panel & Sonar? > > > > Lastly, check you've got the volume up on the FW, sounds kinda dozy, but > I've done it after multiple driver re-installs, when one might become a tad > confused/pissed off? > > > > > > ----- Original Message ----- > > From: clarence griffin <mailto:goldfingas@xxxxxxxxx> > > To: ddots-l@xxxxxxxxxxxxx > > Sent: Tuesday, June 29, 2010 5:02 PM > > Subject: [ddots-l] Re: FW 1884 - no audio > > > > did you set it to the out put device under the audio options? > > > > GF > > > > > > On Jun 29, 2010, at 9:26 AM, Stacy Blackwell wrote: > > > > Hi, guys. Any advice would be appreciated. The FW 1884 > didn't respond after loading Sonar 7, so I went to Options and checked on > its input and ouput port settings. The FW 1884 Control nor its MIDI ports > were listed. So I shut the system down, reset the MIDI and unity gain on > the FW 1884, and rebooted. I found the FW 1884 Control now as a selection > and selected them. The faders began working, but I still have no audio. > When playing a song in Sonar, the meters are stating a peak, so I know it is > playing. I also tapped the end of my monitor amp's cables to hear the sound > in the spekaers, so I know the amp is working. I don't know if this is a > Sonar deal or a Tascam FW 1884 deal. How do I determine where the signal > breakdown is? Thanks in advance. > > > ________________________________ > > > The New Busy think 9 to 5 is a cute idea. Combine multiple > calendars with Hotmail. Get busy. > <http://www.windowslive.com/campaign/thenewbusy?tile=multicalendar&ocid=PID2 > 8326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_5> > > > > > > ________________________________ > > The New Busy is not the too busy. Combine all your e-mail accounts with > Hotmail. Get busy. > <http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28 > 326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4> > > > ________________________________ > > The New Busy is not the too busy. Combine all your e-mail accounts with > Hotmail. Get busy. > <http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28 > 326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4> > > PLEASE READ THIS FOOTER AT LEAST ONCE! > To leave the list, click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe > If this link doesn't work then send a message to: > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > unsubscribe > For other list commands such as vacation mode, > click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=faq or > send a message, to > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > faq > _________________________________________________________________ The New Busy is not the old busy. Search, chat and e-mail from your inbox. http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_3