[ddots-l] Re: using Jaws on same sound-card as Sonar?
- From: "Shawn Brock" <shawn@xxxxxxxxxxxxxx>
- To: <ddots-l@xxxxxxxxxxxxx>
- Date: Fri, 3 Dec 2010 10:38:07 -0800
Hmm, this is interesting Dave.
On my ADK the front jacks are enabled. That's the way it came from them...
Shawn
----- Original Message -----
From: Farfar Carlson
To: ddots-l@xxxxxxxxxxxxx
Sent: Friday, December 03, 2010 10:19 AM
Subject: [ddots-l] Re: using Jaws on same sound-card as Sonar?
Shawn,
That's if the headphone jack has been enabled. On my ADK the headphone out
and line in jacks on the front panel are disabled due to the wiring injecting
noise into the audio stream.
However there are plenty of output jacks on the rear (7, to be precise) with
the SigmaTel board in my unit.
Dave
Composed on a Dell Latitude 630 in the general vicinity of my Audio Recording
and Mixing Studios, San Jose, California
----- Original Message -----
From: Shawn Brock
To: ddots-l@xxxxxxxxxxxxx
Sent: Friday, December 03, 2010 09:18
Subject: [ddots-l] Re: using Jaws on same sound-card as Sonar?
So, run a patch cord with a 1 8th jack from the headphone output on the
front of the ADK Daw, buy a 1 8th to 1 quarter inch adapter, plug into one of
the inputs of the macky you just bought, and your in business. You can set up
2 headphone mixes, 1 for you with Jaws, the other without.
----- Original Message -----
From: Brian Howerton
To: ddots-l@xxxxxxxxxxxxx
Sent: Friday, December 03, 2010 2:45 AM
Subject: [ddots-l] Re: using Jaws on same sound-card as Sonar?
Mike,
That makes sense I think, but for my jaws soundcard, it is built in to my
computer daw...
----- Original Message -----
From: Michael C
To: ddots-l@xxxxxxxxxxxxx
Sent: Friday, December 03, 2010 4:51 AM
Subject: [ddots-l] Re: using Jaws on same sound-card as Sonar?
Hello my name is Mike C from Montreal,
What I do is I have my V-studio 100 for Sonar solly, and line in my
sound blaster card in to one of the inputs of the V-studio.
This way you could have Jaws on the same headphone. I then use my
mackie 1620 onix which has the output of the V-studio, and use a pre amp
headphone system in one of the monitoring busses of the mackie board.
This way my clients are only hearing the music, and not Jaws, while I
hear Jaws through the head phone of the V-studio, as the V-studio has a
separate headphone jack.
Sounds a little complicated, but this system insures the best set up
for my needs.
From: Brian Howerton
Sent: Friday, December 03, 2010 1:54 AM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: using Jaws on same sound-card as Sonar?
Hello Mike!
I have been wondering how to best achieve having jaws and my client
going through the same headphones so I don't have to wear two pairs of
headphones. How do you do this? For my audio interface, I am using the mackie
Onyx 1220I mixer which is a mixer and an audio interface all in one, but how
would this be done or how do you achieve this? Thanks so much mike!
Brian
----- Original Message -----
From: Mike Tyo
To: ddots-l@xxxxxxxxxxxxx
Sent: Friday, December 03, 2010 1:25 AM
Subject: [ddots-l] Re: using Jaws on same sound-card as Sonar?
Brandon,
As you've probably have read from the replies to your inquiry, it's
definitely not recommended. I use a small line mixer that I got for around 60
bucks, and everything works great. The mixer has a headphone jack on it, and
I've got plenty of outputs that I can feed everything to my amp.
Hope this helps.
Mike
----- Original Message -----
From: Brandon Keith
To: ddots-l@xxxxxxxxxxxxx
Sent: Thursday, December 02, 2010 21:46
Subject: [ddots-l] using Jaws on same sound-card as Sonar?
Hello,
If I switched jaws' output to my external sound-card along with
Sonar, would I run into any problems?
Right now I'm wearing two sets of headphones and it's not very
comfortable, so I'd like to just use one.
Thanks,
Brandon Keith
Check out
MySpace: http://www.myspace.com/brandonkeithcom
Also add me on facebook!
brandonkeith
Other related posts:
