As far as putting "Single value data" on a new line, I tend to agree with Bob, it seems to be consistent with all the other formats described in this section. However, I have a different observation about "The user may assign any value...", because when it comes to Reserved_Parameters, the user (of the EDA tool or the model) should not be able to assign or change the value provided in the .ami file. They should only be allowed to do that for Model_Specific parameters at most, but even then, I wonder why the model maker wouldn't use another format type (such as Range, List, etc...) if the user is allowed to change this single valued parameter? Thanks, Arpad ============================================================= -----Original Message----- From: ibis-macro-bounce@xxxxxxxxxxxxx [mailto:ibis-macro-bounce@xxxxxxxxxxxxx] On Behalf Of Bob Ross Sent: Tuesday, April 30, 2013 3:12 PM To: ambrishv@xxxxxxxxxxx; ibis-macro@xxxxxxxxxxxxx Subject: [ibis-macro] Re: A cut and paste error in IBIS v5.1? Ambrish: I disagree with your editorial suggestion. There may be other issues with the definitions of Value, Range, etc., but the existing definition is textually formatted in a way that is parallel to the other definitions -the argument(s) on the same line and the definition under it. Bob -----Original Message----- From: ibis-macro-bounce@xxxxxxxxxxxxx [mailto:ibis-macro-bounce@xxxxxxxxxxxxx] On Behalf Of Ambrish Varma Sent: Tuesday, April 30, 2013 12:00 PM To: ibis-macro@xxxxxxxxxxxxx Subject: [ibis-macro] Re: A cut and paste error in IBIS v5.1? Here's another one: (Page 177) Value <value> Single value data. The user may assign any value without any restrictions within the constraints of the Type of the variable. Should be: Value <value> Single value data Thanks, Ambrish. -----Original Message----- From: ibis-macro-bounce@xxxxxxxxxxxxx [mailto:ibis-macro-bounce@xxxxxxxxxxxxx] On Behalf Of Bob Ross Sent: Tuesday, April 30, 2013 2:47 PM To: Arpad_Muranyi@xxxxxxxxxx; ibis-macro@xxxxxxxxxxxxx Subject: [ibis-macro] Re: A cut and paste error in IBIS v5.1? Arpad: Good catch. That could be added to the list of typo corrections. Bob -----Original Message----- From: ibis-macro-bounce@xxxxxxxxxxxxx [mailto:ibis-macro-bounce@xxxxxxxxxxxxx] On Behalf Of Muranyi, Arpad Sent: Tuesday, April 30, 2013 11:32 AM To: ibis-macro@xxxxxxxxxxxxx Subject: [ibis-macro] A cut and paste error in IBIS v5.1? I think I just found a fairly serious cut and paste error in IBIS v5.1 on pg. 185. Both GetWave_Exists and Use_Init_Output has the same exact sentence for the Definition: "Tells EDA tool whether the AMI_GetWave is implemented in this model" While this is correct for the GetWave_Exists, it is quite wrong for Use_Init_Output... I think this must be corrected for the next version of the specification. Thanks, Arpad ========================================================================== --------------------------------------------------------------------- IBIS Macro website : http://www.eda.org/pub/ibis/macromodel_wip/ IBIS Macro reflector: //www.freelists.org/list/ibis-macro To unsubscribe send an email: To: ibis-macro-request@xxxxxxxxxxxxx Subject: unsubscribe --------------------------------------------------------------------- IBIS Macro website : http://www.eda.org/pub/ibis/macromodel_wip/ IBIS Macro reflector: //www.freelists.org/list/ibis-macro To unsubscribe send an email: To: ibis-macro-request@xxxxxxxxxxxxx Subject: unsubscribe --------------------------------------------------------------------- IBIS Macro website : http://www.eda.org/pub/ibis/macromodel_wip/ IBIS Macro reflector: //www.freelists.org/list/ibis-macro To unsubscribe send an email: To: ibis-macro-request@xxxxxxxxxxxxx Subject: unsubscribe --------------------------------------------------------------------- IBIS Macro website : http://www.eda.org/pub/ibis/macromodel_wip/ IBIS Macro reflector: //www.freelists.org/list/ibis-macro To unsubscribe send an email: To: ibis-macro-request@xxxxxxxxxxxxx Subject: unsubscribe --------------------------------------------------------------------- IBIS Macro website : http://www.eda.org/pub/ibis/macromodel_wip/ IBIS Macro reflector: //www.freelists.org/list/ibis-macro To unsubscribe send an email: To: ibis-macro-request@xxxxxxxxxxxxx Subject: unsubscribe