Normally, yes, Brian. However, perhaps David Holladay will be able to chip in later with some advice. George. > -----Original Message----- > From: duxuser-bounce@xxxxxxxxxxxxx > [mailto:duxuser-bounce@xxxxxxxxxxxxx] On Behalf Of brian Moore > Sent: 25 April 2005 12:02 > To: duxuser@xxxxxxxxxxxxx > Subject: [duxuser] Re: help with a juliet and dbt 10.5 > > Hi George. I suspect it is whatever the default is. I will > call her and check. how should it be set. I have played > with mine so not sure how hers is set. I presume it should > be on since it can then send margin line spacing parameters > to the embosser. correct? > > thanks. > > Brian. > > > *********** REPLY SEPARATOR *********** > > On 4/25/2005 at 11:50 AM George Bell wrote: > > >Hi Brian, > > > >In the Global, Embosser Setup menu, when you select Edit, > under Device > >Settings have you got "Send Escape Codes" > >checked or unchecked? > > > >George. > > > >> -----Original Message----- > >> From: duxuser-bounce@xxxxxxxxxxxxx > >> [mailto:duxuser-bounce@xxxxxxxxxxxxx] On Behalf Of brian > >Moore > >> Sent: 25 April 2005 11:44 > >> To: duxuser@xxxxxxxxxxxxx > >> Subject: [duxuser] help with a juliet and dbt 10.5 > >> > >> Hi all. > >> > >> I have been playing with this customer to try and get this > > > >> sorted out for quite a while now. > >> I have a juliet as well and mine seems to work properly. > >> > >> We have reset the embosser and tried a whole range of > parameters both > >> in the document and global menus to try > >and > >> make this work properly but still a huge margin on the > reverse side > >> of the page. > >> > >> any info would be appreciated. > >> > >> thanks. > >> Today, I made a discovery. There are two paths to > >embossing > >> materials. > >> When you go through Duxbury, open the files in Duxbury, > >and > >> then emboss, the file appears with a wide margin on the > overleaf side > >> of the page. > >> > >> When you print through MS Word, you get interpoint with a > margin of > >> about three spaces on the overleaf side. This > >is progress. > >> previously, I have only printed through Duxbury by > >opening > >> the files and translating and embossing them one by one. > >> > >> There are still questions. What I don't understand is > >that > >> you have to set a margin of 2 to create a margin of one > >cell > >> on the front side of the page. If you don't set the > >margin > >> at 2, the embossing is flush with the perforations of the > >> tractor-feed strips. > >> > >> The big question is why would the emboss feature be > >different > >> depending on how you access Duxbury? > >> > >> > >> > >> > >> * * * > >> * This message is via list duxuser at freelists.org. > >> * To unsubscribe, send a blank message with > >> * unsubscribe > >> * as the subject to <duxuser-request@xxxxxxxxxxxxx>. You > >may also > >> * subscribe, unsubscribe, and set vacation mode and other > >subscription > >> * options by visiting //www.freelists.org. The list > >archive > >> * is also located there. > >> * Duxbury Systems' web site is > >http://www.duxburysystems.com > >> * * * > >> > > > > > > > >This Message has been scanned for viruses by McAfee Groupshield. > >* * * > >* This message is via list duxuser at freelists.org. > >* To unsubscribe, send a blank message with > >* unsubscribe > >* as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also > >* subscribe, unsubscribe, and set vacation mode and other > subscription > >* options by visiting //www.freelists.org. The list archive > >* is also located there. > >* Duxbury Systems' web site is http://www.duxburysystems.com > >* * * > > > > * * * > * This message is via list duxuser at freelists.org. > * To unsubscribe, send a blank message with > * unsubscribe > * as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also > * subscribe, unsubscribe, and set vacation mode and other subscription > * options by visiting //www.freelists.org. The list archive > * is also located there. > * Duxbury Systems' web site is http://www.duxburysystems.com > * * * > This Message has been scanned for viruses by McAfee Groupshield. * * * * This message is via list duxuser at freelists.org. * To unsubscribe, send a blank message with * unsubscribe * as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also * subscribe, unsubscribe, and set vacation mode and other subscription * options by visiting //www.freelists.org. The list archive * is also located there. * Duxbury Systems' web site is http://www.duxburysystems.com * * *