Hey DJX unfortunately the power supply is built right in to the board, and has
to be taken apart to actually gain access to it lol.
In actual fact I took one of my boards apart the other day and know this to be
accurate lol.
Thanks so much for confirming that even thought he port is welded on that its
actually from another company chip set.
I’ve asked Terry to see if he couldn’t gain access to another computer system
before actually putting this to rest lol.
Best
On Oct 1, 2018, at 8:30 AM, DJ X <megamansuperior@xxxxxxxxxxx> wrote:
Hey Mike no prob.
Even though the USB port is soldered on, the USB chipset is most likely a
separate package. Most manufacturers purchase chipsets, only company I’ve
heard of who build their own USB chipsets was RME.
In any case, if he can plug in another device to the computer on the same
port, and it works, it probably is the actual mixer.
It might be as you said, the unit’s power supply. Is it an external brick? Or
is it built in?
Is the unit natively a USB 2 device? Or a USB3?
I’m assuming you guys already did the basic stuff like switch and try a
different wire etc?
Regards, DJX
From: 20304202720n behalf of
Sent: Monday, October 1, 2018 8:12 AM
To: ddots-l@xxxxxxxxxxxxxxxx <mailto:ddots-l@xxxxxxxxxxxxxxxx>
Subject: [ddots-l] Re: update on my soundcraft mtk22
Hey DJX first of all, I just wanted to apologize that I sent out themessage
stating that your content couldn’t bet read, however after a little while, I
was able to re open the message, and all worked fine.
Toanswer your question on why I think it would come down tot he PC in the end
is because the Board stays on when not plugged in to the uSB port of the
computer system.
I have the same issue with one of my computers where the mixer console kept
on turning it self on/off like Terry’s is doing, and when I switched to
another computer, the mixer console functioned just fine.
The FW 1884 Had a separate firewire card built in to the motherboard, where
as the Signature has the port welded directly in to the board.
There has to be a battery of some sorts on the board because the effects
processor is digital, and retains its patch change when you turn off the
board.
It could very well be that the power supply on the mixer console is giving
out, as I just did some research on geersluts and several folks reported
issues with power supply issues.
“sorry Terry”
I suppose we could dance around this problem all night long, but I suggested
to Terry that he call his centre, and speak to them, and they could trouble
shoot the problem, as at this point anything is possible, which is why I’m
not stating what I have stated in previous threads as a 100% solution.
At any rate I’m hoping that terry can resolve this.
Best
On Sep 30, 2018, at 11:32 PM, Michael Ciarciello <m_dsmusic@xxxxxxxx
<mailto:m_dsmusic@xxxxxxxx>> wrote:
Hey DJX your messages have no content lol. Unless my system is going crazy
lol.
On Sep 30, 2018, at 10:43 PM, DJ X <megamansuperior@xxxxxxxxxxx
<mailto:megamansuperior@xxxxxxxxxxx>> wrote:
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx
<mailto:ddots-l-request@xxxxxxxxxxxxx>?subject=unsubscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx <mailto:ddots-l-request@xxxxxxxxxxxxx>
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx
<mailto:ddots-l-request@xxxxxxxxxxxxx>?subjectתq or
send a message, to
ddots-l-request@xxxxxxxxxxxxx <mailto:ddots-l-request@xxxxxxxxxxxxx>
and in the Subject line type
faq
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx
<mailto:ddots-l-request@xxxxxxxxxxxxx>?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx <mailto:ddots-l-request@xxxxxxxxxxxxx>
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx
<mailto:ddots-l-request@xxxxxxxxxxxxx>?subject�q or
send a message, to
ddots-l-request@xxxxxxxxxxxxx <mailto:ddots-l-request@xxxxxxxxxxxxx>
and in the Subject line type
faq
